manualshive.com logo in svg

Titan 5059340256061, Manual, Page: 62 / 79

Share
Download
Titan 5059340256061 Manual Download Page 62

62

TT5MTP26-2

In

 more 

detail

 . . .

Air filter

Inspect the air filter regularly. Clean or replace it with a new one if necessary.

68

A2

Air filter

Locking tab

Locking tab

Cover

Cover

1.  Press the locking tab on the air filter case (A2) and remove its cover (Fig. 68).

2.  Remove the air filter and tap it on a stable surface to remove dust. Use 

compressed air (max. 3 bar) to remove stubborn dust.

3.  Refit the air filter and the cover of the air filter case (A2).

Fuel, fuel lines and fuel filter

The fuel tank of this machine is fitted with a filter located at the free end of the fuel pipe. 

If it is necessary to clean or replace the fuel filter, contact an authorised service centre 

or a similarly qualified person.

 

> Keep fuel fresh (less than 30 days) or add fuel stabiliser.

 

> Empty the fuel tank after every use.

 

> Run the machine dry of fuel in idle before storage.

 

> Replace fuel lines and fuel filters every 2 years.

Care and maintenance

Summary of Contents for 5059340256061
















































































Reviews:

No comments