background image

2

•   Maintain a safe working environment.  The work area should be clean, dry, clutter free, 

 

    and sufficiently lit.

•   Vehicle doors should be closed during the raising and lowering cycles.

•   Closely watch the vehicle and lift during the raising and lowering cycles.

•   Do not operate the lift in explosive atmospheres, such as in the presence of flammable 

 

    liquids, gases, or dust.  Power equipment can create sparks which may ignite flammables.

•   Keep hands, tools, and other extremities from under carriage and moving parts.

•   Never operate this lift with someone on it.

•   Do not allow anyone on the lift or inside a raised vehicle.

•   Keep children and bystanders away from work area.  Do not let children operate or play 

 

    on lift.

•   Wear proper safety attire.  Do not wear loose fitting clothing while operating lift. Long hair, 

     jewelry and sleeves should be secured.

•   Never leave the lift unattended while under a load.

•   Do not operate this lift if under the influence of drugs, alcohol, or medication.  Operator 

 

    must be alert at all times when using heavy lift equipment.

•   Comply with all applicable accident prevention regulations.

•   Only use the vehicle manufacturer’s recommended lifting points.

•   After positioning the vehicle, apply the parking brake.

•   Use caution when removing or installing heavy vehicle components which may result in 

 

    center-of-gravity displacement.

•   Use this lift only for the work it is intended. Do not use this product for an application for 

 

    which it was not designed.  Misuse can lead to personal injury and/or property damage.

        WARNING:

 Prior to completely raising the vehicle, raise the vehicle 6” off the ground 

and check the adapter pads for solid contact by performing the “BUMPER TEST”.  Walk 

around the back of the vehicle and push up and down on the bumper.  The vehicle will rock, 

but should not at any time lose contact with the pads.  If the vehicle is bouncing off the pads 

or feels at all unstable, you should lower it back to the ground and reposition the pads to 

balance the load.  Repeat this process until the vehicle is completely stable.

        WARNING:

 Use this lift only in well ventilated areas.  Carbon monoxide exhausted 

from running vehicle engines is a colorless, odorless fume that, if inhaled, can cause serious 

personal injury or death.

        WARNING:

 People with pacemakers should consult their physician(s) before using 

this product.  Operation of electrical equipment in close proximity to a heart pacemaker could 

cause interference or failure of the pacemaker.

        WARNING:

 This product contains or produces a chemical known to the State of 

California to cause cancer and birth defects (or other reproductive harm). (California Health 

& Safety Code 25249.5 et seq.)

Summary of Contents for HD2P-11000ACX

































Reviews: