Timex Ironman Global Trainer M229 User Manual Download

Page: 5 / 42

Important Safety Instructions and Warnings

1. To prevent risk of fire, chemical burn, electrolyte leak and/or injury from the internal Lithium-polymer

battery:

A. Do not attempt to remove the case-back or exterior shell of the product or remove the non-user-

replaceable battery.

B. Do not leave unit exposed to a heat source or in a high temperature location (such as in the sun

or in an unattended vehicle). To prevent damage store it out of direct sunlight.

C. Do not puncture or incinerate.

D. When storing for an extended time, store within the following temperature range: 32°F to 77°F

(0°C to 25°C).

E. The Global Trainer

™

watch should only be charged within a temperature range of 32°F to 113°F

(0°C to 45°C).

F. Do not operate the unit outside of the following temperature range: -4°F to 131°F (-20°C to 55°C).

G. Contact your local waste disposal department to properly recycle/ dispose of the unit/battery.

2. Use only the Phihong PSB05R-050Q power adapter supplied with this product.
3. This is not a medical device and is not recommended for use by persons with serious heart conditions.

You should always consult your physician before beginning or modifying an exercise program.

4. Consulting the speed+distance system while moving is unsafe and distracting, and could result in accident

or collision. Use the memory functions to later review your performance data. See the instructions

for details.

5. Interference with the radio signal, poor contact between your skin and the chest strap, and other factors

may prevent accurate transmission of heart rate data.

Introduction

While all of the settings described in the User Guide can be made on the Global Trainer

™

watch, it is

easier to use your computer to customize your watch through the Timex

Device Agent software.

See

www.timexironman.com/deviceagent

for the Timex Device Agent made for your computer’s

operating system.

Global Trainer

™

Software Version

Because the Global Trainer

™

watch can be customized to show languages in addition to English for its

displays and messages, the screens shown in these instructions will be available on your watch in your

selected language. The exceptions are: the default View Screen names (SWIM, BIKE, RUN, CUSTOM 1,

CUSTOM 2), the default TIMER names, the default COURSE names, and the default BIKE settings.

The Timex

Ironman

Global Trainer

™

Bodylink

System is a comprehensive performance-monitoring device

that incorporates SiRFstarIII

GPS technology and ANT+

™

sensor integration for multiple activities to provide

a powerful workout and training tool. To view or print a copy of any of the instructions for the Global Trainer

™

watch or its accessories, go to:

http://www.timex.com/info/Product_Instruction_Guides_Downloads

This guide reflects the latest instructions for Global Trainer software version

2.8X.

To determine your watch’s

version; press MODE to go to CONFIGURE, press

to GPS, press

to VERSION and press

You can update

the Global Trainer software through instructions posted on the Timex Device Agent downloadable to your

computer desktop.
For more information on the Timex Ironman Global Trainer watch and its capabilities, please visit the Videos

section of the Training Resources page at

www.timexironman.com

Feature Overview

•

INDIGLO

Night-Light with Night-Mode

Feature and Continuous Illumination –

The INDIGLO

night-

light illuminates the display with the press of the INDIGLO

button. When activated, the Night-Mode

feature illuminates the display with any button press.

For added convenience during low-light conditions, the Global Trainer

™

watch comes with an option for

continuous illumination of the display. See the section on Operational Buttons and Icons for further details.

•

Performance Mode –

Keep track of multiple variables during your workout, including speed, distance,

elapsed time, pace, and calories burned.

• Multisport Mode –

Incorporate several activities and transition periods into a single workout, and track

all of them together.

• Customizable Screen Displays –

View up to four workout metrics of your choosing in each of five view

screens for either Performance or Multisport Modes, so your unique workout information is always

at your fingertips.

Summary of Contents for Ironman Global Trainer M229











































Search results

Summary of Contents for Ironman Global Trainer M229

Reviews:

Related manuals for Ironman Global Trainer M229

Brands by name

Popular brands

Timex Ironman Global Trainer M229, User Manual

Search results

Summary of Contents for Ironman Global Trainer M229

Reviews:

Related manuals for Ironman Global Trainer M229

Brands by name

Popular brands