background image

3

Status Bar

The status bar appears at the bottom of all screens. It shows the battery charge remaining, the current time, 

and status icons to give an at-a-glance view of the Global Trainer

 watch’s status.

Battery icon

Shows the approximate charge of the battery. More dark 

segments indicates a higher charge. The icon shows the charge 

remaining while charging, plus the remaining section to charge 

blinks.

t

Chrono icon

Appears when the chronograph is running.

d

Alarm icon

Appears when the alarm is set.

H

Timer icon

Appears when the chrono is running and a timer has been 

enabled.

2:00 PM

Time of Day text

Current time

g

Heart icon

Solid: 

Heart rate monitor is communicating properly.

 

Blinking:

 Device is pairing or has received no useful data for 

15 seconds.

RPM icon

Solid: 

Bike speed or cadence sensor is communicating properly.

Blinking:

 Device is pairing or has received no useful data for 

15 seconds.

Power icon

Solid: 

Power meter is communicating properly.

Blinking:

 Device is pairing or has received no useful data for 

15 seconds.

Satellite icon

Solid: 

GPS has a satellite fix.

Blinking:

 GPS is seeking a satellite fix.

None: 

GPS cannot locate a satellite.

Charge Your Global Trainer

 Watch

Before you use the Global Trainer

 watch for the first time, the lithium-ion battery must be charged. 

A depleted battery takes approximately 2 1/2 to 3 1/2 hours to fully charge. 

CAUTION: 

The Global Trainer

™ 

watch should only be charged within a temperature range of 32°F - 113°F 

(0°C - 45°C).

Charge Using the USB Cable

1.   Insert the large USB-A plug on the download/charging clip into a USB port on any powered computer. 
2.   Attach the download/charging clip to the back of the Global Trainer

 watch. 

3.   Make sure the four contacts on the clip touch the four metal discs on the back of the watch. Match the 

red dot on the watch with the red dot on the connector for proper orientation. 

4.   Secure the clip to the watch caseback by placing the fixed end of the clip into the slot adjacent to the  

red dot and locking the hinged end of the clip into the other slot.

Charge Using the AC Adaptor

1.   Insert large USB-A plug on the download/charging clip into the USB port on the AC adaptor, and plug the 

AC adaptor into an electrical outlet. 

2.   Attach the download/charging clip to the back of the Global Trainer

 watch, as instructed above in steps 

3

 

and 4.

The Power Off Function is set to SHOW TIME, so the date and time will display during charging. A blinking 

battery icon appears during charging. A solid battery icon appears when charging is complete. 

  Use only the Phihong PSB05R-050Q power adaptor supplied with this product.

NOTE: 

To prevent corrosion, please dry the download/charging contacts and the surrounding area on the back 

of the Global Trainer

 watch.

Turn the Global Trainer

 Watch On and Off

To turn the Global Trainer

™ 

watch on or off, press and hold 

8

 for 2 seconds until you hear a three-note tone. 

The tone ascends in pitch when powering on, and descends in pitch when powering off.

Because the Power Off Function is set to SHOW TIME, the date and time will display when the Global Trainer

™ 

watch is turned off. The POWER OFF label will appear in the upper status bar.
When the Power Off Function is set to TURN OFF DISPLAY, better standby battery life is obtained. To learn 

more about the Power Off Function, refer to the CONFIGURE (Mode) and the MODES sections of this USER 

GUIDE.

NOTE: 

The display contrast can change due to temperature changes. To adjust the contrast level, follow 

these steps.

Summary of Contents for Ironman Global Trainer M229











































Reviews: