ASSEMBLY
Assembly Section 2-27
FINAL PREPARATION FOR OPERATION
Place operator’s safety and operation decals on the steering column and side console
where they are clearly visible to the operator. These decals should be understood by
each operator of the machine in conjunction with the Safety and Operation Sections of
this book. The decals are to be maintained in good condition as a reminder to the
operator, and should be replaced if damaged.
All bosses, pins and pivot points will need to be greased as instructed in the
Maintenance Section of this manual. The hydraulic reservoir can also be filled with the
recommended fluid (see Maintenance Section) and the filter installed in the top of the
tank. Double check all fittings and fasteners BEFORE starting tractor. Also secure any
loose hoses together with zip ties and wrap with split hoses where friction may occur on
the hoses.
BEFORE starting or operating the tractor you must read and understand the
Safety and Operation Sections of this manual completely.
BE SURE THE BALL VALVES ARE OPEN!
Start tractor and allow instruments to
stabilize. Using a piece of paper or cardboard as noted in the Safety and Maintenance
Sections, check all fittings and connections for hydraulic leaks.
If a leak is found, you must shut down the tractor and set the cutter on the ground.
Before attempting to fix the leak, you must actuate the lift valve handles several times to
relieve any pressure in the lines.
Before operating the mower
, the cutter head and boom should be slowly moved
throughout the full range of motion. Watch for any condition that would cause pinching or
excess stress on the hoses. The steering and front axle travel should also be carefully
moved through their full range of motion. If any condition occurs in which the hoses
contact the tires, the steering and / or front axle travel may need to be limited as
described in the tractor operator’s manual. This should also be done if the tires rub, or
are extremely close to any other part of the mower, such as the hydraulic tank or draft
beam. This may include adding shims or adjusting stop bolts in the tractor front to solve
the problem. While checking motion, you should also check that the control circuits are
connected according to the operator’s decal for the valve handles.
MOWER TESTING
Take the tractor to a place free of loose objects on the ground. Operate the cylinders
through their full range of motion again, to clear the lines of air. Follow the instructions in
the Operation Section to operate the mower. Vibration of the mower should be minimal
at all times. After a 5 minute test run, the knife bolts should be retorqued, and retorqued
once again after the first few hours of operation.
If any parts of this Assembly Section, or any other section of this manual
are not clearly understood you must contact your dealer or the address on
the front of this manual for assistance!
(ASM-C-0010)
Summary of Contents for JD5085-5115M T4F
