Thrane&Thrane sailor 6217 User And Installation Manual Download Page 68

Page: 68 / 102

Chapter 3: Installation

Power, VHF antenna and external equipment

ACC connector

Use the connector marked

ACC

to connect GPS input and/or a chart plotter that

supports AIS.

The interface for GPS is NMEA 0183 (EN61 162-1 NMEA0183/ EN61 162-2
NMEA0183 Highspeed).

To connect a chart plotter that supports AIS, connect the NMEA output wires
from the VHF radio to the NMEA input on the chart plotter.

The AIS receiver is enabled by default. It can be turned off to reduce power
consumption. For instructions how to turn it off see

System setup

on page 67.

Note

The chart plotter must support NMEA highspeed (38400 baud).

Warning!

Before connecting the VHF radio to a chart plotter, ensure
that the power is turned off on both devices.

Brown, Pin 1, NMEA in+

Blue, Pin 2, NMEA in-

For waterproof installation use

rubber vulcanizing tape

White, Pin 3, NMEA out-

Green, Pin 4, NMEA out+

GPS Cable (NMEA 0183)/

Chart Plotter Cable

99-131043-A

Summary of Contents for sailor 6217







































































































Search results

Summary of Contents for sailor 6217

Reviews:

Related manuals for sailor 6217

Brands by name

Popular brands

Thrane&Thrane sailor 6217, User And Installation Manual

Search results

Summary of Contents for sailor 6217

Reviews:

Related manuals for sailor 6217

Brands by name

Popular brands