background image

InTRoDUCTIon

P3

English

safetyPrecautions

y

y

Never open the receiver cover. It is dangerous to touch the inside of the receiver due to 

high voltage currents and possible electrical hazards and your warranty will be void. Refer all 

maintenance or servicing to suitably qualified personnel.

y

y

When you are connecting cables, be sure that the receiver is disconnected from the mains 

supply voltage. Wait a few seconds after switching off the receiver before you move the 

receiver or disconnect any equipment.

y

y

It is a necessity that you only use an approved extension and compatible wiring that is suitable 

for the electrical power consumption of the installed equipment. Please ensure that the 

electrical power supply corresponds with the voltage on the electrical identification plate at the 

back of the receiver.

If the receiver does not operate normally, even after strictly following the instructions in this user 

manual it is recommended to consult your dealer or the appropriate service for your country.

1.2storage

Your receiver and its accessories are stored and delivered in a packaging designed to protect 

against electric shocks and moisture. When unpacking it, make sure that all the parts are 

included and keep the packaging away from children. For transporting the receiver from one 

place to another or if you are returning it under warranty conditions, make sure to repack the 

receiver in its original packaging with its accessories. Failing to comply with such packaging 

procedures could void your warranty.

1.3Equipmentset-up

We recommend you to consult a professional installer to set up your equipment. Otherwise, 

please follow the instructions below:

y

y

Refer to the user manual of your TV and your antenna.

y

y

Make sure that the SCART/HDMI cable and outdoor components are in a good condition and 

the SCART/HDMI connections are well shielded and from good quality.

This manual provides complete instructions for installing and using this receiver. The following 

symbols will serve as follow.

WaRnIng:

 

 Indicates a warning information.

note:

 

 Indicates any other additional important or helpful information.

mEnU

 

 Represents a button on the remote control or the receiver 

(bold

character)

Move

 

to

 

Represents a menu item within a screen (

Italic

 

character

)

1.4accessories

y

y

User manual

y

y

1x remote control

y

y

2x batteries (AAA type)

y

y

1x adaptor 12 V DC, 2.0 A

WaRnIng:

   The batteries should not be recharged, disassembled, electrically short-circuited, be mixed or 

used with other types of batteries. If rechargeable accumulators instead of batteries are going 

to be used, we recommend using (e.g. NiMH) types with low self-discharge to ensure long time 

operation of remote control.

1.5UsageofexternalUsbdevices

y

y

THOMSON cannot guarantee compatibility to all types of USB storage devices.

y

y

It is advised not to store important information on USB storage devices used with the receiver.

y

y

Always make backups of data on your USB storage device before using it with this receiver.

y

y

THOMSON will not take responsibility for any loss of information or circumstances caused by 

loss of information.

Summary of Contents for THS812




























Reviews: