Think 3D STORMBEE S20 User Manual Download | Manualshive

Page: 30 / 102

background image

STORMBEE User Manual

–

Think 3D BVBA

Version N°1.1, last modified 30/09/2018

16

Figure 4.2 Battery charging process step 2

4.1.2.1

Without battery charging hubs (2 batteries max)

If you only want to charge two batteries simultaneously (instead of three or more, see section ), then
you don't need the charging hubs and can connect the batteries directly to the two ports of the main
charger.  Please  be  aware  that  the  battery  charger  and  its  charging  hubs  have  (yellow)  male  XT90
connectors  and  STORMBEE's  batteries  have  200A  (black)  female  connectors.  Therefore  custom
conversion connector were made and provided to be able to connect the STORMBEE batteries to the
battery charger and its hubs.

3.

Connect both the power cables and the balancer cable of each battery to the charger.
Otherwise the battery charger will refuse to charge the battery.

«
...
28
29
30
31
32
...
»

Summary of Contents for STORMBEE S20







































































































Reviews:

No comments

Related manuals for STORMBEE S20

Brand: TRNDlabs Pages: 29

Brand: sky viper Pages: 2

Brand: DarwinFPV Pages: 18

Brand: C-Fly Pages: 24

Brand: LDARC Pages: 12

Brand: LDARC Pages: 11

Brand: LDARC Pages: 11

Brand: LDARC Pages: 12

Brand: LDARC Pages: 12

Brand: Keyshare Pages: 11

Brand: ATOMRC Pages: 9

Brand: JJRC Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands