pg. 8
The casing on the EASY model is factory-mounted before being packaged. To move the heater from the pallet the casing and the 2 screws that secure
the heater to the wood pallet must firstly be removed.
4
4
4
4
4
INST
INST
INST
INST
INSTALLA
ALLA
ALLA
ALLA
ALLATION
TION
TION
TION
TION
4 . 1
4 . 1
4 . 1
4 . 1
4 . 1
HEA
HEA
HEA
HEA
HEATER / BOILER L
TER / BOILER L
TER / BOILER L
TER / BOILER L
TER / BOILER LOCA
OCA
OCA
OCA
OCATION
TION
TION
TION
TION
CAUTION : Always use trolleys to move the appliance and the appliance must always be in a vertical position. The casing for the H2O is packed
separately. To unpack the Compact, once the wood crate has been removed, remove the casing (in reverse order as set out in par.4.2.3).
Remove the screw at the base of the heater / boiler and remove the base from the bottom pallet. Follow the general guidelines set out in
paragraph 1.1 to the letter. Above all ensure that the flooring of the room where the heater / boiler will be installed is capable of bearing the weight
of the appliance plus the weight of the water contained in it and the weight of the pellets in the hopper.
CAUTION: The room in which the appliance will operate must be adequately ventilated (minimum air intake 1300 m3/h).
The heater / boiler must be positioned at a minimum safe distance
from walls and furnishings. This distance will have to be
increased considerably if the objects surrounding the appliance
are inflammable (matchboarding, furniture, curtains, picture
frames, sofas, etc...). The recommended minimum distances are
illustrated in the drawing below on the right.
Installation in the vicinity of heat-sensitive materials is only
permitted if suitable insulating protection is placed between the
object and the appliance (ref. Uni 10683).
4 . 2 . 1
4 . 2 . 1
4 . 2 . 1
4 . 2 . 1
4 . 2 . 1
MOUNTING MET
MOUNTING MET
MOUNTING MET
MOUNTING MET
MOUNTING METAL
AL
AL
AL
ALCOL
COL
COL
COL
COLOR / EASY
OR / EASY
OR / EASY
OR / EASY
OR / EASYCASING FOR HEA
CASING FOR HEA
CASING FOR HEA
CASING FOR HEA
CASING FOR HEATER H2O
TER H2O
TER H2O
TER H2O
TER H2O
450 mm SE MATERIALE COMBUSTIBILE
45
0
mm
SE
M
AT
ER
IAL
E C
OM
BU
ST
IBI
LE
45
0
mm
SE
M
AT
ER
IAL
E C
OM
BU
ST
IBI
LE
ISOLANTE TERMICO
450 mm SE MATERIALE
COMBUSTIBILE
After positioning and levelling the heater by raising or lowering the mounting feet, connecting it to the heating system and to the electrical system
(see par.4.4 , 4.5 , 4.6 , 4.7 , 4.8 , 4.9 , 4.10, 4.11 ),
proceed to mount the casing as illustrated:
Carry out the procedure described below and follow the drawing on the next page:
- Remove the cover
(A)
.
- Open the cover
(D)
, remove the screw
(C)
and remove the cover
(E)
.
- Fasten the 4 spacers
(I)
with the supplied nuts M4
(H)
and screws M4x16
(L)
to the lower base.
- Adjust the heater mounting feet and position the kickplates
(M)
as illustrated, making sure that the kickplates are inserted under the plate
(PT)
;
then check that the door can be easily removed
(PC)
and if necessary raise the feet.
- Mount the side panels by firstly inserting the lower holes on the spacers
(I)
that were fastened beforehand.
- Fasten the screws
(F)
to lock the side panels
(G)
.
- Mount the cast iron cover
(E)
, the cover
(A)
and fasten the screw
(C)
.
4 . 2
4 . 2
4 . 2
4 . 2
4 . 2
MOUNTING HEA
MOUNTING HEA
MOUNTING HEA
MOUNTING HEA
MOUNTING HEATER
TER
TER
TER
TER
/ BOILER
/ BOILER
/ BOILER
/ BOILER
/ BOILER
CASING
CASING
CASING
CASING
CASING .....
KEY
450 mm if the
material is
combustible
Heat insulating
material
LEGENDA
450 mm se
materiale
combustibile
Isolante termico