Thermo Scientific RC 3BP Plus Instruction Manual Download Page 55

Page: 55 / 70

Maintenance and Care

Autoclaving the rotors

7-6

Sorvall RC 3BP Plus

Thermo Scientific

Autoclaving the rotors

1. Before autoclaving clean rotor and accessories as described above.

2. Place the rotor on a flat surface.

•

Rotors and adapter can be autoclaved at 121° C.

•

The maximum permissible autoclave cycle is 20 minutes at 121° C.

Clean the rotor before autoclaving and rinse it with distilled water. Remove all accessories (tubes,
adapters). Place the rotor on a flat surface.

Service of Thermo Fisher Scientific

Thermo Fisher Scientific recommends having the centrifuge and accessories serviced once a year by an
authorized service technichian. The service technicians check the following:

•

the electrical equipment

•

the suitability of the set-up site

•

the lock and the safety system

•

the rotor

•

the fixation of the rotor and the drive shaft

Thermo Fisher Scientific offers inspection and service contracts for this work.

Note

No chemical additives are permitted in the steam.

CAUTION

Never exceed the permitted temperature and duration when autoclaving.

If the rotor shows signs of corrosion or wear, it must be replaced.

Summary of Contents for RC 3BP Plus







































































Search results

Summary of Contents for RC 3BP Plus

Reviews:

Related manuals for RC 3BP Plus

Brands by name

Popular brands

Thermo Scientific RC 3BP Plus, Instruction Manual

Search results

Summary of Contents for RC 3BP Plus

Reviews:

Related manuals for RC 3BP Plus

Brands by name

Popular brands