Thermo Scientific iCAP RQ ICP-MS Pre-Installation Requirements Manual Download Page 50

Page: 50 / 71

Consumables

Gas Supply

Thermo Scientific

iCAP RQ Pre-Installation Requirements Guide (P/N BRE0009927, Revision A)

5-9

iCAP RQ ICP-MS 1-Channel Systems: Hydrogen mixtures with Helium (for QCell)

NOTICE

The maximum content for hydrogen is 4.5%.

▲

See

Table 5-6

for details of the hydrogen gas requirements.

iCAP RQ ICP-MS 2-Channel Systems: Hydrogen or mixtures with Helium (for QCell)

NOTICE

A hydrogen sensor must be installed in the vicinity of the

instrument.

▲

See

Table 5-7

for details of the hydrogen gas requirements.

Supply Rate

max. 10 mL/min per channel

Pressure min.

0.05 MPa

(0.5 bar)

max. 0.15 MPa (1.5 bar)

using a two-stage pressure
regulator (200 bar to 3 bar)

Table 5-5.

CCT gas requirements for helium, continued

Gas Requirement

Specification

Table 5-6.

Gas requirements for hydrogen 1-channel system

Gas Requirement

Specification

Purity

99.999% or better

Maximum Water Content

2 ppmv

Supply Rate

max. 10 mL/min per channel

Pressure min.

0.05 MPa

(0.5 bar)

max. 0.15 MPa (1.5 bar)

using a two-stage pressure
regulator (200 bar to 3 bar)

Table 5-7.

Gas requirements for hydrogen 2-channel system

Gas Requirement

Specification

Purity

99.999% or better

Maximum Water Content

2 ppmv

Summary of Contents for iCAP RQ ICP-MS








































































Search results

Summary of Contents for iCAP RQ ICP-MS

Reviews:

Related manuals for iCAP RQ ICP-MS

Brands by name

Popular brands

Thermo Scientific iCAP RQ ICP-MS, Pre-Installation Requirements Manual

Search results

Summary of Contents for iCAP RQ ICP-MS

Reviews:

Related manuals for iCAP RQ ICP-MS

Brands by name

Popular brands