Thermo Scientific EASY-Spray NG User Manual Download Page 20 | Manualshive

Page: 20 / 62

background image

1

Introduction

Functional Description

6

EASY-Spray Series Ion Source User Guide

Thermo Scientific

Controller Power Supply

The installation method for the EASY-Spray Series ion source includes the controller power
supply when using an LC instrument other than the EASY-nLC 1200. For instructions, see

Powering the Ion Source for Other nanoLC/MS Systems

shows the controller power supply assembly that consists of a wall-mounted power

supply with a detachable input plug and a power adapter cable. The other end of the power
adapter cable connects to the input power socket (labeled P-BUS) located on the bottom of
the ion source to provide the 24 Vdc input for the temperature controller PCB.

Figure 5.

Controller power supply assembly (shown with a European input plug)

Note

The total length of the output cord and power adapter cable is approximately

274 cm (9 ft). Make sure that an electrical wall outlet is within reach for the power supply
and that you provide suitable clearance around it for cooling.

Power adapter cable

Power supply with output cord

«
...
18
19
20
21
22
...
»

Summary of Contents for EASY-Spray NG































































Reviews:

No comments

Related manuals for EASY-Spray NG

Brand: ICS Schneider Messtechnik Pages: 124

Brand: OfiTE Pages: 21

Brand: Earthlite Pages: 4

Brand: YATEK Pages: 78

Brand: Raymarine Pages: 70

Brand: Harbor Freight Tools Pages: 4

Brand: GE Pages: 698

Brand: EarthQuake Pages: 28

Brand: TAIKO Audio Pages: 24

Brand: National Instruments Pages: 10

Brand: Qlight Pages: 4

Brand: P-Q Controls Pages: 5

Brand: Zell Pages: 32

Brand: Uflex Pages: 16

Air 2000 Outdoor

Brand: ubbink Pages: 21

Brand: Vari Lite Pages: 14

Brand: Vaniman Pages: 3

Brand: Yuwell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands