manualshive.com logo in svg

Thermo Scientific EASY-Spray NG, User Manual, Page: 23 / 62

Share
Download
Thermo Scientific EASY-Spray NG User Manual Download Page 23

 

2 

Installing the EASY-Spray Series Ion Source

Attaching the Ion Source

Thermo Scientific

EASY-Spray Series Ion Source User Guide

9

Powering the Ion Source for Other nanoLC/MS Systems

Follow this procedure to connect the power supply that is provided with the ion source. 

To connect the controller power supply to the ion source

1. Turn the ion source’s temperature knob to the OFF position. 

2. If not already connected, connect the detachable input plug and power adapter cable to 

the power supply (

Figure 5

). 

3. Connect the power adapter cable to the P-BUS socket located on the bottom of the ion 

source as follows: 

a. Align the red dot on the plug with the red dot on the right side of the socket 

(

Figure 6

). 

b. Push the plug into the socket. 

4. Plug the power supply into an electrical wall outlet. 

Attaching the Ion Source

Follow these procedures to install the EASY-Spray Series ion source. 

•

To install the ion source onto the MS

•

To install the optional Tee holder under the column holder

CAUTION  

To avoid an electric shock, always use the detachable input plug that is 

appropriate for your country or region and comes with the power supply. 

CAUTION  

After completing the power supply connections, route the output cord so that 

it is not a trip hazard. 

Tip  

The EASY-Spray NG ion source (ES082) ships with the Tee holder attached to the 

column holder. If you have the EASY-Spray ion source (ES081), you can order the 
optional Tee holder to support the venting Tee; see 

Chapter 8, “Replaceable Parts.” 

Summary of Contents for EASY-Spray NG































































Reviews:

No comments