Thermo Scientific EASY-Spray NG User Manual Download Page 24 | Manualshive

Page: 24 / 62

background image

2

Installing the EASY-Spray Series Ion Source

Attaching the Ion Source

10

EASY-Spray Series Ion Source User Guide

Thermo Scientific



To install the ion source onto the MS

CAUTION

Before you touch an ion source that was recently in use or touch its

components, allow the system to cool for a minimum of 20 minutes.

CAUTION

• Make sure that you do not accidentally lift the release lever located at the top of the

API source interface, which could interfere with or prevent installation of the ion
source.

• To avoid contaminating the ion transfer tube, do not touch its exposed entrance.

Note

You might need to use a small slotted screwdriver to loosen the screws on the

ion sweep cone. The spray cone is directly behind the ion sweep cone.

Align the source mounting holes with the MS pins and carefully
attach the source. Then, lock the source levers.

Unlock both locking levers
(EASY-Spray NG shown).

2

3

If the ion sweep cone is installed, let it cool to room temperature,
and then remove it by grasping its outer ridges and pulling it off.

1

High voltage (HV)
connector

Spring-loaded bolt delivers
HV to the column

«
...
22
23
24
25
26
...
»

Summary of Contents for EASY-Spray NG































































Reviews:

No comments

Related manuals for EASY-Spray NG

Brand: Fender Pages: 15

Brand: Raven Pages: 27

Brand: Raven Pages: 79

Brand: Raven Pages: 88

Brand: DARAY Pages: 24

Brand: Jafar Pages: 9

Brand: Xo Pages: 59

Brand: Garelick Pages: 2

Brand: Garelick Pages: 2

Brand: Gardigo Pages: 32

Brand: Madrigal Pages: 5

Brand: MacDon Pages: 504

Brand: QRS Pages: 16

Brand: QMAXZ Lighting Pages: 36

Brand: NAMYSLO Pages: 13

Brand: Walimex Pro Pages: 44

Brand: Otto Bock Pages: 72

Brand: Nuvo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands