Thermo Scientific EASY-Spray NG User Manual Download Page 60

Page: 60 / 62

Contents of the Installation Kits

EASY-Spray Series Ion Source User Guide

Thermo Scientific

Tools:

• Emitter positioning tool

• 3 mm hex key

1 set

ES232

A/B mixing/venting Tee, stainless steel,
with three attached ferrules and nuts
(for 1/16 in. OD tubing)

1 set

SC901

Tee holder (for the mixing/venting Tee)

ES234

Sleeves, PEEK, 1/16 in. OD

IDEX™, F-233

Wash cap (for the EASY-Spray column)

ES235

The EASY-Spray NG source housing comes with the EASY-Spray NG Ion Source Kit (P/N ES082) and cannot
be purchased separately.

The EASY-Spray source housing comes with the EASY-Spray Ion Source Kit (P/N ES081) and cannot be
purchased separately.

The ion source kit includes either the analog camera (P/N ES216) with the LCD monitor (P/N ES217) or the
USB camera with a USB extension cord.

Table 8.

Contents of the EASY-Spray Series ion source kits (Sheet 2 of 2)

Image

Description

Quantity

Part number

Summary of Contents for EASY-Spray NG































































Search results

Summary of Contents for EASY-Spray NG

Reviews:

Related manuals for EASY-Spray NG

Brands by name

Popular brands

Thermo Scientific EASY-Spray NG, User Manual

Search results

Summary of Contents for EASY-Spray NG

Reviews:

Related manuals for EASY-Spray NG

Brands by name

Popular brands