Thermo Scientific EASY-Spray NG User Manual Download Page 36

Page: 36 / 62

Connecting the EASY-Spray Column Plumbing

Using the nanoViper Fitting

EASY-Spray Series Ion Source User Guide

Thermo Scientific

ii. In the EASY-Spray dialog box, press the temperature box, enter a temperature

value in the range 30–60 °C, press

Accept

, and then press

Set

and

Close

–or–

• (RSLCnano system) Use the temperature control knob on the front of the ion source.

Table 5

lists the display readings that can appear on the actual temperature display.

Using the nanoViper Fitting

For some LC instruments, the plumbing connects to the EASY-Spray column through several
nanoViper fittings, such as the one shown in

Figure 12

. Although these fittings can withstand

ultra-high-performance LC (UHPLC) backpressures up to 1200 bar (17 400 psi), they are
fingertight fittings that require only very small torques to seal. Therefore, you must follow the
next procedure to avoid damage by overtightening.

Figure 12.

nanoViper fitting

IMPORTANT

If you later manually turn the temperature control knob, you

must repeat this procedure to reset the touch-screen value.

Table 5.

Readings for the actual temperature display

Display

Description

EASY-Spray column is not connected.

Actual temperature while heating up

Actual temperature, stabilized

b.L.

Disconnect and reconnect power to the ion source to exit boot
loader mode (b.L.).

No display

See

Replacing the Temperature Controller PCB

Tip

Refer to the packing for your nanoViper fittings to determine compatibility with

either the 1000 bar capillaries (beige tubing) or the 1200 bar capillaries (blue tubing).

PEEK sealing surface

Removable knurled tightening tool

Screw

Summary of Contents for EASY-Spray NG































































Search results

Summary of Contents for EASY-Spray NG

Reviews:

Related manuals for EASY-Spray NG

Brands by name

Popular brands

Thermo Scientific EASY-Spray NG, User Manual

Search results

Summary of Contents for EASY-Spray NG

Reviews:

Related manuals for EASY-Spray NG

Brands by name

Popular brands