Thermo Scientific EASY-Spray NG User Manual Download Page 50

Page: 50 / 62

Maintenance

Replacing the Temperature Controller PCB

EASY-Spray Series Ion Source User Guide

Thermo Scientific

Replacing the Temperature Controller PCB

If the temperature controller PCB becomes damaged, the actual temperature display might
remain off and the EASY-Spray column might not heat. Follow this procedure to install a new
PCB.



To replace the temperature controller PCB

1. Follow the procedure

To remove the ion source from the MS

2. Using a 2.5 mm hex key, remove the four hex screws located on the bottom of the ion

source. If you previously installed the temperature controller PCB, P/N ES233, in the
EASY-Spray source, remove the additional cover plate (

Figure 23

Figure 23.

EASY-Spray ion source (bottom) with the new temperature controller PCB
and extra cover plate

3. Slowly pull out the enclosure for the temperature controller PCB (

Figure 24

Figure 24.

Temperature controller PCB (P/N ES233)

CAUTION High voltage.

To prevent electric shock, make sure that you disconnect the

P-Bus cable before you remove the PCB.

Note

The cover plate is for use on the EASY-Spray ion source (ES081) only when

installing the ES233 temperature controller PCB.

IMPORTANT

If you remove the temperature controller PCB too quickly or at an

angle, you might damage the PCB components or the internal heater cable routed
above the PCB.

EASY-Spray housing

Temperature controller
PCB (ES233)

Cover plate

Summary of Contents for EASY-Spray NG































































Search results

Summary of Contents for EASY-Spray NG

Reviews:

Related manuals for EASY-Spray NG

Brands by name

Popular brands

Thermo Scientific EASY-Spray NG, User Manual

Search results

Summary of Contents for EASY-Spray NG

Reviews:

Related manuals for EASY-Spray NG

Brands by name

Popular brands