![background image](http://html1.mh-extra.com/html/thermo-king/914970/914970_manual_1104406129.webp)
Refrigeration Service Operations
127
Heat Exchanger
Removal
1. Remove the refrigerant charge.
2. Remove the evaporator top cover.
3. Remove the mounting bolts that hold the heat
exchanger on the bulkhead.
4. Disconnect the equalizer line from the suction
line.
5. Disconnect liquid outlet line flare nut from the
expansion valve.
6. Note the position of the feeler bulb on the side
of the suction line. Remove the expansion
valve feeler bulb from the suction tube.
7. Unsolder the suction line at the evaporator coil
end.
8. Unsolder the remaining outlet suction line and
inlet liquid line connections from the
condenser side of the bulkhead. Remove putty
from around the lines before unsoldering the
connections.
9. Lift the heat exchanger assembly out of the
evaporator housing.
Installation
1. Clean the tubes for soldering.
2. Place the heat exchanger assembly in the
evaporator housing and install the mounting
hardware loosely.
3. Solder liquid inlet and suction outlet line
connections on the condenser side of the
bulkhead. Seal openings through bulkhead
with putty when refrigerant lines have cooled
off.
4. Tighten the heat exchanger mounting
hardware securely.
5. Solder suction line connection to the
evaporator coil.
6. Connect the equalizer line flare fitting to the
suction line and liquid outlet line flare fitting
to the expansion valve.
7. Pressurize the low side and test for leaks. If no
leaks are found, evacuate the unit.
8. Clean the suction tube to a bright polished
condition. Install the feeler bulb clamps and
feeler bulb on the side of the suction line in its
former position. The feeler bulb must make
good contact with the suction line or operation
will be faulty. Wrap with insulating tape.
9. Open the refrigeration valves and place the
unit in operation. Install refrigerant charge.
10. Test the unit to see that the expansion valve is
properly installed.
High Pressure Cutout Switch
Removal
1. Install gauge manifold set.
2. Start the unit and pump down the low side.
3. Stop the unit.
4. Bleed high side to low side using gauge set.
5. Disconnect the wires and remove the high
pressure cutout switch from the discharge
tube.
Installation
1. Apply a refrigerant Loctite
TM
to the threads of
the high pressure cutout switch.
2. Install and tighten high pressure cutout switch
and reconnect the wires.
3. Pressurize the refrigeration system and test for
leaks. If no leaks are found, evacuate the
system.
High Pressure Relief Valve
Removal
1. Remove the refrigerant charge.
2. Unscrew and remove the high pressure relief
valve.
Installation
1. Apply a refrigerant Loctite
TM
to the threads of
the high pressure relief valve.
2. Install and tighten the high pressure relief
valve.
Summary of Contents for 914970
