Texas Instruments SimpleLink CC2652RB, Manual

Page: 19 / 70

8.13 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - RX
When measured on the CC26x2RBEM-7ID reference design with T
c
= 25 °C, V
DDS
= 3.0 V, f
RF
= 2440 MHz with
DC/DC enabled unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX
path.
All measurements are performed conducted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Receiver sensitivity PER = 1% –100 dBm
Receiver saturation PER = 1% > 5 dBm
Adjacent channel rejection
Wanted signal at –82 dBm, modulated interferer at
±5 MHz, PER = 1%
36 dB
Alternate channel rejection
Wanted signal at –82 dBm, modulated interferer at
±10 MHz, PER = 1%
57 dB
Channel rejection, ±15 MHz or
more
Wanted signal at –82 dBm, undesired signal is IEEE
802.15.4 modulated channel, stepped through all
channels 2405 to 2480 MHz, PER = 1%
59 dB
Blocking and desensitization,
5 MHz from upper band edge Wanted signal at –97 dBm (3 dB above the
sensitivity level), CW jammer, PER = 1%
57 dB
Blocking and desensitization,
10 MHz from upper band edge Wanted signal at –97 dBm (3 dB above the
sensitivity level), CW jammer, PER = 1%
63 dB
Blocking and desensitization,
20 MHz from upper band edge Wanted signal at –97 dBm (3 dB above the
sensitivity level), CW jammer, PER = 1%
63 dB
Blocking and desensitization,
50 MHz from upper band edge Wanted signal at –97 dBm (3 dB above the
sensitivity level), CW jammer, PER = 1%
66 dB
Blocking and desensitization,
–5 MHz from lower band edge Wanted signal at –97 dBm (3 dB above the
sensitivity level), CW jammer, PER = 1%
60 dB
Blocking and desensitization,
–10 MHz from lower band edge Wanted signal at –97 dBm (3 dB above the
sensitivity level), CW jammer, PER = 1%
60 dB
Blocking and desensitization,
–20 MHz from lower band edge Wanted signal at –97 dBm (3 dB above the
sensitivity level), CW jammer, PER = 1%
63 dB
Blocking and desensitization,
–50 MHz from lower band edge Wanted signal at –97 dBm (3 dB above the
sensitivity level), CW jammer, PER = 1%
64 dB
Spurious emissions, 30 MHz to
1000 MHz
Measurement in a 50-Ω single-ended load –66 dBm
Spurious emissions, 1 GHz to
12.75 GHz
Measurement in a 50-Ω single-ended load –53 dBm
Frequency error tolerance
Difference between the incoming carrier frequency
and the internally generated carrier frequency
> 350 ppm
Symbol rate error tolerance
Difference between incoming symbol rate and the
internally generated symbol rate
> 1000 ppm
RSSI dynamic range 95 dB
RSSI accuracy ±4 dB
8.14 Timing and Switching Characteristics
8.14.1 Reset Timing
PARAMETER MIN TYP MAX UNIT
RESET_N low duration 1 µs
8.14.2 Wakeup Timing
Measured over operating free-air temperature with V
DDS
= 3.0 V (unless otherwise noted). The times listed here do not
include software overhead.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
MCU, Reset to Active
(1)
850 - 4300 µs
MCU, Shutdown to Active
(1)
850 - 4300 µs
www.ti.com
CC2652RB
SWRS232D – FEBRUARY 2019 – REVISED FEBRUARY 2021
Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 19
Product Folder Links: CC2652RB