Texas Instruments J721EXSOMXEVM User Manual Download Page 63 | Manualshive

Page: 63 / 85

background image

J721E EVM Hardware Architecture

63

SPRUIS4A – December 2019 – Revised May 2020

Submit Documentation Feedback

Copyright © 2019–2020, Texas Instruments Incorporated

Jacinto7 J721E/DRA829/TDA4VM Evaluation Module (EVM)

MCU CAN1

The MCU CAN1 port of J721E SoC is connected to the CAN transceiver Mfr. Part# TCAN1042HGVD. A
2-pin header J34 (68002-202HLF) is provided inline for user probe option. This port does not support
WAKE function. The signals MCU_MCAN1_H and MCU_MCAN1_L are terminated to a 3-pin header J31
(FCI: 68001-403HLF) with 120E split termination.

The STB signal is an active High signal held high with external pull up by default. The GPIO control from
MCU domain provided to pull the line low.

MAIN CAN0 (Supports WAKE function)

The MAIN CAN0 port of J721E SoC is connected to the CAN transceiver with Wake function supported
device TCAN1043-Q1. A 2-pin header J24 (68002-202HLF) is provided inline for user probe option.

The output of the CAN transceiver is terminated to a 4-pin header J27 (61300411121).

The signals MCAN0_H and MCAN0_L are routed as differential signals with 120E impedance with split
termination. The STB signal is an active low signal held low with integrated pull down by default.

The VCC supply (5V) to the transceiver is derived from a Step-Up converter.

Hardware WAKEn input for the CAN interface is provided using a push-button SW12.

Figure 47. CAN Wake Push Button

«
...
61
62
63
64
65
...
»

Summary of Contents for J721EXSOMXEVM






















































































Reviews:

No comments

Related manuals for J721EXSOMXEVM

Brand: fadini Pages: 32

Brand: ON Semiconductor Pages: 20

Brand: C&T Solution Pages: 65

Brand: Linear Technology Pages: 10

Brand: Icop Pages: 40

SKR E3 DIP V1.0

Brand: BIGTREETECH Pages: 10

B560M DS3H PLUS

Brand: Gigabyte Pages: 42

Brand: Gigabyte Pages: 80

Brand: Texas Instruments Pages: 18

X58 PLATINUM SLI - Motherboard - ATX

Brand: MSI Pages: 74

Brand: Avalue Technology Pages: 116

Brand: EVGA Pages: 1

Brand: QDI Pages: 47

Brand: ON Semiconductor Pages: 5

Brand: Advantech Pages: 104

Brand: Commell Pages: 53

Brand: Biostar Pages: 60

S2257 THUNDER 2400

Brand: TYAN Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands