background image

 
 
 
Laboratory mortar mixer 
1.0206.07

 

 

 

3. 

Basic safety instructions 

3.1  Obligations of the operator 

 
The operating instructions must be easily accessible and kept in the immediate vicinity 
of  the  mortar  mixer.  Only  sufficiently  qualified  operating  personnel  may  work  with  the 
mortar  mixer.  The  operating  personnel  must  be  trained  before  handling  the  mortar 
mixer. Check to see that the operating personnel have read and understood the operat-
ing  instructions.  Define  the  exact  responsibilities  for  the  operating  personnel.  Provide 
personal protective equipment to all operating personnel. 
 
The  person  operating  the  device  must  ensure  that  both  themselves  and  other  people 
are not endangered. 
 
If the operating safety of the mortar mixer is impaired by defects or damage, the mortar 
mixer should be taken out of operation immediately and used again only after all of the 
sources of danger have been eliminated. 
 
 

3.2  Requirements for the operating personnel 

 
Only qualified specialist personnel who have been instructed by the operator may work 
on the mortar mixer. The minimum age for the operator is 18 years. Individuals under 
the age of 18 may only operate the mortar mixer under the supervision of a qualified 
skilled worker. The operator is responsible for third parties in the working area. 
 
 

3.3  Obligations of the operating personnel 

 
The operating personnel must read the operating instructions carefully before handling 
the mortar mixer. Please always observe the safety instructions. Wear personal protec-
tive equipment when handling the mortar mixer. 
 
 

3.4  Workplace 

 
The workplace is located at the control panel in front of the mortar mixer. The workplace 
is intended to be used with the connected peripheral equipment provided by the cus-
tomer. Accordingly, the operator must ensure that it is safe. The workplace’s design is 
also based on the applicable requirements from the German Health and Safety at Work 
Regulations (Betriebs-Sicherheits-Verordnung, BetrSichV) and the analysis of work-
place hazards. 
 
 

 

Summary of Contents for 1.0206.07



















































Reviews: