background image

 
 
 
Laboratory mortar mixer 
1.0206.07

 

 

 

38 

 

14  Warranty 

 
Our 

general terms of sale and delivery

 apply in principle. 

 
The  manufacturer  warrants  that  these  operating  instructions  were  compiled  in  accor-
dance with the technical and functional parameters of the supplied mortar mixer. 
The manufacturer reserves the right to add supplemental information to these operating 
instructions. 
 
The manufacturer grants the statutory warranty. 
Wear parts are excluded from this warranty. 
 
The guarantee of the manufacturer that the machine will remain in perfect working order 
is contingent on compliance with the provisions of this operating manual and use of the 
equipment as intended. 
 
The  manufacturer  disclaims  liability  for  damage  resulting  from  improper  usage  of  the 
mortar mixer or failure to comply with the guidelines and suggested conduct in this op-
erating manual. 
 
Warranty claims to the manufacturer are excluded if the mortar mixer is subject to unau-
thorized changes in structure or in its functional design without the written agreement of 
the manufacturer. 
 
 

15.  Issue date of the operating instructions 

 

3rd edition 

May 2010 

 

16.  Copyright 

 
The copyright remains with 
 

TESTING Bluhm & Feuerherdt GmbH 

 
These operating instructions are intended only for the operator and his/her personnel. It 
contains specifications and instructions that may not be 
 
 

 

replicated 

 

 

distributed or 

 

 

communicated by other means. 

 
Infringements are punishable under criminal law. 
 

Summary of Contents for 1.0206.07



















































Reviews: