Terex Genie GS-1530 Page 89 Service And Repair Manual Download

Page: 89 / 341

March 2021

Service and Repair Manual

Steer Axle Components

Part No. 1272217GT

™

-30 • 32 • 46 • 47

How to Remove a Drive Motor

1 Block the non-steer tires.
2 Remove the cotter pin from the wheel castle

nut of the motor to be removed.

3 Note: Always replace the cotter pin with a new

one when removing the castle nut.

4 Loosen the wheel castle nut. Do not remove

it.

5 Raise the machine approximately 2 inches /

5 cm. Place blocks under the chassis for

support.

Crushing hazard. The chassis

will fall if not properly supported.

6 Remove the wheel castle nut. Remove the

wheel.

7 Tag, disconnect and plug the hydraulic hoses

on the drive motor. Cap the fittings on the

drive motor.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

Component damage hazard.

Hoses can be damaged if they

are kinked or pinched.

8 Remove the drive motor mounting fasteners.

Remove the motor.

Torque specifications

Drive motor mounting fasteners,

dry

75 ft-lbs

101.7 Nm

Drive motor mounting fasteners,

lubricated

56 ft-lbs

76.3 Nm

6-2

Steer Cylinder

How to Remove the Steer

Cylinder

Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Block the non-steer tires.
2 Remove the pin retaining fasteners from the

rod-end pivot pin. Remove the pivot pin.

Note: While removing the pin retaining fasteners,

take note of the quantity and location of the

spacers when removing the pivot pin.
3 Remove the pin retaining fasteners from the

barrel-end pivot pin. Remove the pin.

Note: While removing the pin retaining fasteners,

take note of the quantity and location of the

spacers when removing the pivot pin.
4 Remove the steer cylinder from the machine.
5 Tag, disconnect and plug the hydraulic hoses

from the steer cylinder. Cap the fittings on the

cylinder.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

Component damage hazard.

Hoses can be damaged if they

are kinked or pinched.

Summary of Contents for Genie GS-1530






















































































































































































































































































































































Search results

Summary of Contents for Genie GS-1530

Reviews:

Related manuals for Genie GS-1530

Brands by name

Popular brands

Terex Genie GS-1530, Service And Repair Manual

Search results

Summary of Contents for Genie GS-1530

Reviews:

Related manuals for Genie GS-1530

Brands by name

Popular brands