manualshive.com logo in svg

Terasic DE10-Standard, User Manual, Page: 66 / 126

Share
Download
Terasic DE10-Standard User Manual Download Page 66

 

 

 

 

DE10-Standard  
User Manual 

65 

 

www.terasic.com

 

January 19, 2017 

 

           

Figure 5-3

 shows the block diagram of audio recorder and player design. There are hardware and 

software  parts  in  the  block  diagram.  The  software  part  stores  the  Nios  II  program  in  the  on-chip 
memory. The software part is built under Eclipse in C programming language. The hardware part is 
built under Qsys in Quartus II. The hardware part includes all the other blocks such as the “AUDIO 
Controller”, which is a user-defined Qsys component and it is designed to send audio data to the 
audio chip or receive audio data from the audio chip.   

The audio chip is programmed through I2C protocol, which is implemented in C code. The I2C pins 
from the audio chip are connected to Qsys system interconnect fabric through PIO controllers. The 
audio chip is configured in master mode in this demonstration. The audio interface is configured as 
16-bit I2S mode. 18.432MHz clock generated by the PLL is connected to the MCLK/XTI pin of the 
audio chip through the audio controller.

 

                 

 

Figure 5-3 Block diagram of the audio recorder and player

 

 

 

Demonstration Setup, File Locations, and Instructions 

 

Hardware project directory: DE10_Standard_Audio 

 

Bitstream used: DE10_Standard_Audio.sof 

 

Software project directory: DE10_Standard_Audio\software 

 

Connect an audio source to the Line-in port   

 

Connect a Microphone to the MIC-in port   

 

Connect a speaker or headset to the Line-out port 

 

Load the bitstream into the FPGA. (note *1) 

 

Load the software execution file into the FPGA. (note *1) 

 

Configure the audio with SW0, as shown in 

Table 5-1

.   

Summary of Contents for DE10-Standard































































































































Reviews:

No comments