Terasic DE10-Standard User Manual Download Page 54

Page: 54 / 126

DE10-Standard
User Manual

www.terasic.com

January 19, 2017

HPS.

Figure 3-35 Connections between Cyclone V SoC FPGA and G-Sensor

Table 3-26 Pin Assignment of G-senor

Signal Name

FPGA Pin No.

Description

I/O Standard

HPS_GSENSOR_INT PIN_B22

HPS GSENSOR Interrupt Output

3.3V

HPS_I2C1_SCLK

PIN_E23

HPS I2C Clock (share bus with LTC)

3.3V

HPS_I2C1_SDAT

PIN_C24

HPS I2C Data (share bus)

3.3V

The board has a 14-pin header, which is originally used to communicate with various daughter

cards from Linear Technology. It is connected to the SPI Master and I2C ports of HPS. The

communication with these two protocols is bi-directional. The 14-pin header can also be used for

GPIO, SPI, or I2C based communication with the HPS. Connections between the HPS and LTC

connector are shown in

Figure 3-36,

and the pin assignment of LTC connector is listed in

Table

3-27

Summary of Contents for DE10-Standard































































































































Search results

Summary of Contents for DE10-Standard

Reviews:

Terasic DE10-Standard, User Manual, Page: 54 / 126

Search results

Summary of Contents for DE10-Standard

Reviews: