Tennant 8210D Operator'S Manual Download Page 25

Page: 25 / 110

OPERATION

8210D 330210 (1--98)

5. Exit the DISPLAY MAINT. function by

pressing the TENNANT logo switch until all

six maintenance mode screens have been

displayed.

6. Turn the key to the off position.

DISABLING THE MAINTENANCE MODE
When the maintenance mode is disabled, the

flashing icon and alarm will not appear and sound

when the machine is started if one or more of the

maintenance timers goes past its recommended

interval.

1. Turn the machine off.

2. Press and hold the TENNANT logo button

while turning the ignition key to the ON

position. DO NOT start the engine. The ON

position is between the STOP and START

positions. Continue to press the TENNANT

logo button until the RESET PRESSURE

screen appears on the display. Release the

logo button.

3. Press and release the TENNANT logo

button two more times. The SELF TEST

screen will appear on the display.

4. Press the switch next to ENABLE MAINT.

NOTE: If the light next to the ENABLE MAINT.

switch is not illuminated, the maintenance mode is

currently disabled.

NOTE: When the maintenance mode is disabled,

the maintenance timers continue to record the

elapsed time between maintenance intervals. To

view the elapsed time between each of the six

default maintenance intervals, press the switch

next to Display Maint.. Press the TENNANT logo

button to scroll through the maintenance function

screens.

12 : 16 PM

0021

351653

Self Test

Display Maint.

Enable Maint.

351657

Summary of Contents for 8210D















































































































Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands

Tennant 8210D, Operator'S Manual

Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands