Tennant 8210D Operator'S Manual Download Page 64

Page: 64 / 110

OPERATION

8210D 330210 (1--98)

Problem

Cause

Remedy

Little or no solution flow to the

Solution tank empty.

Fill solution tank.

floor.

Solution flow switch turned off.

Turn solution flow switch on.

Solution supply lines plugged.

Flush solution supply lines.

ES switch off.

Turn ES switch on.

Manual control valve nearly closed Open valve more

Poor scrubbing performance.

Debris caught on scrub brushes.

Remove debris.

Improper detergent or brushes

used.

Check with TENNANT

representative for advice.

Worn scrub brushes.

Replace scrub brushes.

ES system does not fill solution

t k

Clogged solution pump or lines.

Flush ES system.

tank.

ES float stuck.

Clean floats of debris.

Clogged ES pump filter.

Clean filter.

Water levels too low in tanks.

Add water.

Summary of Contents for 8210D















































































































Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands

Tennant 8210D, Operator'S Manual

Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands