Tennant 8210D Operator'S Manual Download Page 74

Page: 74 / 110

MAINTENANCE

8210D 330210 (11--98)

AIR FILTER

The engine air filter housing has a dust cap and a

dry cartridge-type air filter element. Empty the

dust cap daily. The air filter must be replaced

whenever the filter element is damaged or when

the optional air filter indicator shows a restriction.

The air filters cannot be cleaned.

Machines with the heavy duty air filter (option)

have a safety element inside the the standard

element. Replace the inner element after the

regular element becomes damaged or has been

changed three times.

Install the dust cap on the air filter housing with

the arrows pointing up.

Replace the air filter element only when the air

filter indicator shows restriction in the air intake

system. Do not remove the air filter element from

the housing unless it is restricting air flow.

02492

Summary of Contents for 8210D















































































































Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands

Tennant 8210D, Operator'S Manual

Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands