Tennant 8210D Operator'S Manual Download Page 36

Page: 36 / 110

OPERATION

8210D 330210 (1--98)

OPERATOR SEAT

The standard operator seat has a position

adjustment lever that allows the operator to move

the seat forward or backward to the desired

position.

Adjust: Pull the lever outward and slide the seat

to the desired position, then release the lever.

DELUXE SUSPENSION SEAT (OPTION)

The deluxe suspension seat can be adjusted

according to the operator’s weight, desired back

rest angle, and desired front--to--back position.

The operator weight adjustment lever has three

different positions: lightweight, middleweight, and

heavyweight.

Adjust: Pull the lever up for the lightweight

position. Move the lever to middle for the

middleweight position. Push the lever down for the

heavyweight position.

The back rest angle knob adjusts the angle of the

back rest.

Adjust: Turn the knob clockwise to decrease or

counter--clockwise to increase the angle of the

back rest.

The seat position lever adjusts the seat forward or

backward.

Adjust: Pull the lever outward and slide the seat

to the desired position, then release the lever.

Summary of Contents for 8210D















































































































Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands

Tennant 8210D, Operator'S Manual

Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands