Tennant 8210D Operator'S Manual Download Page 88

Page: 88 / 110

MAINTENANCE

8210D 330210 (1--98)

REPLACING THE SCRUB BRUSHES

1. Stop the engine.

2. Set the machine parking brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

3. Press the brush spring clip ends together

with your thumb and index finger to remove

the scrub brush. Repeat for the other

brushes.

4. When replacing scrub brushes, start with the

center brush, if applicable. Slide the new

scrub brush under the scrub brush drive

assembly.

5. Line up the scrub brush drive socket with the

drive plug.

6. Press the brush spring clip together and lift

the scrub brush onto the drive plug. Release

the spring clip when the brush is in place.

Repeat for the other brushes.

SOLUTION SYSTEM

RECOVERY TANK

Recovered solution collects in the recovery tank.

The recovery tank should be drained and cleaned

daily, or when the recovery tank full light comes

on.

ES option: The ES filter inside the tank should be

cleaned daily.

Summary of Contents for 8210D















































































































Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands

Tennant 8210D, Operator'S Manual

Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands