Tennant 8210D Operator'S Manual Download Page 101

Page: 101 / 110

MAINTENANCE

8210D 330210 (12--00)

MACHINE JACKING

Empty the hopper, recovery tank, and solution

tank before jacking the machine. You can jack up

the machine for service at the designated

locations. Use a hoist or jack that will support the

weight of the machine. Always stop the machine

on a flat, level surface and block the tires before

jacking the machine up.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

The front jacking locations are on the flat bottom

edge of the front of the machine frame next to the

front tires.

The rear jacking location is under the left side of

the rear bumper.

FOR SAFETY: When servicing machine,

jack machine up at designated locations

only. Block machine up with jack

stands.

STORING MACHINE

Before storing the machine for an extended time,

the machine needs to be prepped to lessen the

chance of rust, sludge, and other undesirable

deposits from forming. Contact Tennant service

personnel.

Summary of Contents for 8210D















































































































Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands

Tennant 8210D, Operator'S Manual

Search results

Summary of Contents for 8210D

Reviews:

Related manuals for 8210D

Brands by name

Popular brands