Tenda FH456 Page 80 User Manual Download

Page: 80 / 82

Appendix

4 Safety and Emission Statement

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures. This device complies with EU

1999/5/EC.

NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is

recommended to use a shielded RJ45 cable.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is

Summary of Contents for FH456



















































































Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands

Tenda FH456, User Manual

Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands