Tenda FH456 User Manual Download

Page: 71 / 82

Specify Additional Settings

Note

During the restoration, do not disconnect the power of the Router and other relevant devices.

2. Strongly recommend you not to restore the Router, unless the following sequence appears:



You have to access the Router but you cannot remember the login name and password.



Your Router does not work well, and you want to reconfigure it by following the Setup Wizard.



You cannot access the Internet, and Tenda technical support recommends you to restore to factory

default.

Export Syslog

If you want to have a good knowledge of system operation, or when you have difficulties in surfing

the Internet, you need to send your system logs to Tenda technical supporters, you can go to this field

to export your Royer’s syslog.

Just click

Export

, then the syslog will be downloaded to your computer.

Firmware Upgrade

Tenda official website offers the latest software version for your Router. Follow steps below to

upgrade the device if you want.

Configuration

❶

Download the firmware file from Tenda official website

http://www.tendacn.com

, save and

unzip it to your local computer.

❷

Click

Browse…

locate and select the upgrade file (

.bin

file) you saved.

Summary of Contents for FH456



















































































Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands

Tenda FH456, User Manual

Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands