Tenda FH456 Page 23 User Manual Download

Page: 23 / 82

Specify Your Internet Settings

Wireless Connection

If you connect to the Router wireless, refer to the following info:

When the following page appears, it indicates that you can access the Internet now.

The wireless

connection will disconnect.

You need to use the new WiFi name and password you set in Quick

Setup Wizard to connect to the Router again.

When the following page appears, it indicates that you cannot access the Internet.

The wireless

connection will disconnect.

You need to use the new WiFi name and password you set in Quick

Setup Wizard to connect to the Router again.

And Log in to the Router’s User Interface, check the

Connection Status

on the

Status

page, and try solving the problem according to the onscreen

instructions. Please refer to

Internet Connection Status

for details.

Summary of Contents for FH456



















































































Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands

Tenda FH456, User Manual

Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands