Telguard TG-1 Express CDMA Installation Manual Download Page 2 | Manualshive

Page: 2 / 38

background image

56049201

ii

© 2016 Telguard

Important Note

The registration form must be completed before leaving for the job site to
install the Telguard product.

There are two ways to register a Telguard unit:



Register online at

www.TelguardOnline.com

, or



Submit the online registration form at

www.telguard.com

,

Foreword

The Telguard model TG-1 Express (p/n TG1LAX01) cellular alarm
communicator is UL Listed for Household Fire systems and Household
Burglary systems. This means that the TG-1 Express may be used in Household
Burglary systems, Household Fire systems or combined Household Burglary &
Fire system as the primary communication path.

Technical Support

Technical support for all Telguard products is available Monday through
Saturday.

Toll Free: 800-229-2326, option 9
Monday - Saturday 8am - 8pm EST

«
1
2
3
4
...
»

Summary of Contents for TG-1 Express CDMA







































Reviews:

No comments

Related manuals for TG-1 Express CDMA

Brand: HAFURY Pages: 60

Brand: ZEN Pages: 62

Brand: T-Mobile Pages: 4

Brand: UMX Pages: 12

Brand: Hammer Pages: 11

Aastra 480i SIP

Brand: ADTRAN Pages: 29

Brand: SLIDE Pages: 32

Brand: SoftBank Pages: 36

Brand: Manta Pages: 28

Brand: Gplus Pages: 68

Brand: Ericsson Pages: 37

Brand: Samsung Pages: 184

Brand: Samsung Pages: 184

R520_CJ16_MM_111009_F4

Brand: Samsung Pages: 169

Renown SCH-U810

Brand: Samsung Pages: 169

Brand: Samsung Pages: 222

Brand: Samsung Pages: 231

S105 - SGH Cell Phone

Brand: Samsung Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands