Telguard Dual Path Series Installation & Operating Manual Download Page 18 | Manualshive

Page: 18 / 42

background image

TG-7 Dual Path Series Installation & Operating Guide

12

56052601 Rev B © 2022 Telguard

UL and ULC Compliance

The TG-7 Dual Path Series communicators are certified as complying with UL and ULC Standards for
Commercial Fire and Commercial Burglary installations. The chart on Page 1 shows the associated
UL and ULC Standards. Certificates of Compliance are available at

portal.telguard.com

UL/ULC Compliance Note:

The alarm panel must also be UL, ULC, or cUL Listed for commercial

fire and/or commercial burglary use as appropriate

.

ULC Compliance Note:

For Commercial Fire installations in Canada, the radio frequency warning

label (supplied with the TG-7FE) must be affixed to the outside front cover of the TG-7FE.

«
...
16
17
18
19
20
...
»

Summary of Contents for Dual Path Series











































Reviews:

No comments

Related manuals for Dual Path Series

Brand: NEC Pages: 2

Yealink SIP-T48G

Brand: Yealink Pages: 9

Yealink SIP-T42G

Brand: Yealink Pages: 2

Brand: i-mobile Pages: 58

Brand: QUO Pages: 28

Brand: Wistec Pages: 60

Brand: UTStarcom Pages: 54

Brand: Proolin VoIP Tech Pages: 25

Brand: ALIGATOR Pages: 13

2 VOICE 1083/58

Brand: urmet domus Pages: 60

Brand: Sagem Pages: 90

Brand: Mobistel Pages: 96

Brand: Hisense Communications Pages: 24

Brand: Zte Pages: 60

Brand: AEI Pages: 4

Brand: Ericsson Pages: 60

Brand: Sony Pages: 5

Brand: Sony Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands