Telguard Dual Path Series Installation & Operating Manual Download Page 5

Page: 5 / 42

TG-7 Dual Path Series Installation & Operating Guide

Table of Contents

Repair and Warranty

Future Testing and Limitations on Use

Terms and Conditions for Use of Telguard Product

Table of Contents

General Description and Operation

Information Related to Software Settings Fire Systems

Information Related to Software Settings Burglary Systems

Features

Operating Mode

Multiple Alarm Format Support

Complete Supervision of Communication Path

Link Supervision

Complete Power Supervision

Telguard Automatic Self-test Report

Telguard Check Status Capability

Programmable Supervisory Trip Output (STC) Relays

Post-Installation Remote Programming

Diagnostic and Status LEDs

Optional DC Operation (12VDC or 24VDC)

Complete Factory Reset Option

UL and ULC Compliance

Getting Ready

Dealer Account Establishment

Pre-Installation Checklist

PCB Layout

Installation

Summary

Step 1: Register the Telguard Unit

Step 2: Physically Install the Communicator in Desired Location

Step 3: Determine Antenna Placement for Best Performance

Step 4: Make Communications Connections and Activate

Step 5: Connect Supervisory Trip Outputs

Step 6: Connect and Test the Trip Input (optional)

Step 7: Connect Tamper Switch (optional in fire-only systems/required for burg)

Appendix 1 Connection Guide

Summary of Contents for Dual Path Series











































Search results

Summary of Contents for Dual Path Series

Reviews:

Related manuals for Dual Path Series

Brands by name

Popular brands

Telguard Dual Path Series, Installation & Operating Manual

Search results

Summary of Contents for Dual Path Series

Reviews:

Related manuals for Dual Path Series

Brands by name

Popular brands