manualshive.com logo in svg

Telemark TT-6, Instruction Manual

Share
Download
Telemark TT-6 Instruction Manual Download Page 29

7 

Place the front-panel switch  "control/sweep select" in the 

"sweep select" position. 

Telemark TT-6 Power Supply 

B  Switch the Sweep Select Module's control-select toggle-switch 

(labeled  "manual/auto';  to 'manual.' Turn the rotary switch 

labeled  "select" to pattern-bank channel 1. 

9 

Switch the channel's mode switch to  "man" (manual). 

10 

Bring the E-beam Power Supply's Emission up slowly and use 

the Sweep Select's channel  1 position knobs to center the 

beam in the crucible pocket.  Turn the Emission down. 

11 

Repeat the last three steps for each of the other pattern-bank 

channels. 

12 If more than one Sweep Select Module is to be used (for 

additional pattern storage), it is advisable to center the 

channels at this time. 

XV Sweep with Memory Module Operation 

The system is now operational.  The position of the E-beam in the crucible can be 

moved or swept by adjustment of the Sweeper removable module controls. 

Patterns are determined using the Controller/Joystick Module while watching the 

E-beam in the vacuum tank's EB gun crucible.  Once setup and positioned, they

can be copied to Sweep Select  Module pattern-bank channels even with Emission

off:  visually match front-panel LED bargraph-display motions controlled by the

joystick system with those controlled by the Sweep Select channels.  Once

patterns are complete, it is best to check them with low Emission into the tank.

Note The E-beam shape may be affected somewhat as Emission output is later 

increased to high levels.  If the E-beam spreads, the pattern may end up 

sweeping wider areas than previously calibrated. 

CAUTION:  always keep the E-beam in the crucible pocket. 

Power Supply Shutdown 

1  Reduce the EMISSION ADJUST potentiometer to zero.  The 

indicated emission current should go to zero.  If it does not, the 

bias setting is too high and should be reduced. 

2 

Turn off the high voltage and emission by depressing the OFF 

push-button.  The indicated voltage level will go to zero. 

Note: Allow two minutes for the unit to cool down before 

proceeding. 

OPERATION 

5-3 

Summary of Contents for TT-6


































Reviews:

No comments

Brands by name

Popular brands

Load more brands