manualshive.com logo in svg

Telemark TT-6, Instruction Manual

Share
Download
Telemark TT-6 Instruction Manual Download Page 15

Telemark TT-6 Power Supply 

This interlock insures that there is sufficient vacuum within the tank before the 

source can be energized.  This level of vacuum normally coincides with that 

required for the energizing of vacuum gauge filaments and most units have 

auxiliary contacts for this purpose.  Their connection should be such that pins 3 

and 11 of J102 are shorted when the filaments of the vacuum gauge are 

energized. 

Remote Emission Adjust - J103 

The front panel mode switch must be set to 

AUTO 

to use the remote 

voltage-control input. 
Remote Emission Adjust is a differential input.  Install the rate signal (zero to -1 O 

volts) pin 3 and ground to pin 4 of J 103. The amplitude of this signal should 

increase when it is desired to increase the evaporation rate. 
The power supply can also be turned on and off remotely.  This is accomplished 

by connecting a normally-closed momentary switch across terminals 5 and 6 of 

J103 and a normally-open switch across terminals 1 and 2. Depressing the 

normally-open switch will turn the power supply on and depressing the normally 

closed switch will turn it off.  Logic level signals are provided to indicate the 

operation of the power supply. A positive signal (12 or 24 volts selected by J1 O on 

mother board) at pin 9 of J103 indicates that the power supply and filament 

controller is energized. A signal at pin 7 is present when the power supply is in 

cutback because of an arc.  Pin 8 is a hard TTL low signal when HV/Emission is 

engaged. 
If the customer needs to use the remote input,  but no external switches are 

available or desired; move the motherboard jumper J11 to the 

ON BYPASS

position and put an external jumper wire across J103 pins 5 and 6.  (Note: If you 

have Rev.Dor later mother board PCB, jumper J14 Off Bypass is provided to 

eliminate external jumper.)  This allows on/off operation from the manual 

controller, while still switched to the AUTO mode, using the remote voltage-control 

input. 

Main Cabinet 

See Figure the 

system 

schematic, 3-B 

Electrical, interlock and control connections are outlined in the following sections. 

Installation should only be performed by qualified personnel. 

POWER IN - TB1 

CAUTION - GREEN WIRE MUST BE CONNECTED TO UTILITY 

GROUND. IT MUST NOT BE  DISCONNECTED 

OR BE CONNECTED TO ANY OF THE HOT LINES. 

When the power supply has been installed as described in the preceding 

sections, the primary power should be the last connection made, with the power 

INSTALLATION 

3-5 

Summary of Contents for TT-6


































Reviews:

No comments

Brands by name

Popular brands

Load more brands