manualshive.com logo in svg

Telemark TT-6, Instruction Manual

Share
Download
Telemark TT-6 Instruction Manual Download Page 14

Telemark TT-6 Power Supply 

to the base of the transformer.  Make sure connections at both ends are to clean 

bare metal.  This insures that the transformer core does not rise above ground 

potential during operation. 
Approximately 15 feet (3.81  meters) of high voltage coaxial cable is provided for 

connection of the power supply output to the source transformer.  One end of this 

cable is permanently terminated within the power supply cabinet. The free end 

passes through the rear panel and goes to source filament transformer. 

Approximately 5 inches (.127mm) of outer covering and shield should be 

removed so that the insulated center conductor is exposed.  This should be 

connected to the center tap. The shield should be connected to the tank ground 

at the transformer.  The same care should be taken in making these connections 

as that taken in connecting earth ground to the tank and transformer. 

Cabinet to Control Module - J101 

See Figure  1-A,  3-C,  3-0,  and 4-A 

There is a 25-pin D type connector located on the front panel of the HV module; it 

is the same as the J101  located on the back panel.  The 25 wires carry many 

signals both for commands and feedback information in analog form. This cable 

connects the power supply to the Control Module. The Control Module is 

available in handheld or rack mounted. 

Interlock Connections - J102 

The external interlocks are connected to the power supply through J102, which is 

located on the rear of the cabinet.  See Figure 3-0, Control Module Connections 

for details.  22 AWG (0.34mm2) ribbon cable or round cable should be used for 

the interlock  installation that is described below. 

WARNING -ALL STATEMENTS REGARDING OPERATOR AND 

EQUIPMENT SAFETY ARE VOID IF THE EXTERNAL 

INTERLOCKS ARE NOT INSTALLED AS REQUIRED. 

•

WATER 

-

Source Water Interlock

Install a water flow switch in the return line of the cooling system for the electron 

beam source.  This switch should close when there is sufficient water flow to cool 

the source and associated shields.  Connect the switch to pins 1 and 9 of J102. 

•

DOOR 

-

Tank High Voltage Access

These interlocks are to be connected to pins 2 and 10 of J102.  Install series 

connected, normally open switches on the doors and high voltage panels so that 

they are closed only when the doors of the chamber and all panels are in place. 

This interlock should be closed only when there is no possible chance of coming 

into contact with high voltage. 

•

VACUUM 

-

High Vacuum Interlock

3-4  INSTALLATION

Summary of Contents for TT-6


































Reviews:

No comments

Brands by name

Popular brands

Load more brands