manualshive.com logo in svg

Telemark TT-6, Instruction Manual

Share
Download
Telemark TT-6 Instruction Manual Download Page 20

Telemark TT-6 Power Supply 

CONTROLS AND 

INDICATORS 

Control Module - Power Supply 

Please refer to Fig.  4-A,  Control Module Front View. 

This section provides a description of the functions of the controls and indicators 

located on the handheld control module. 

1 

HIGH VOLTAGE/EMISSION, OFF - The on/off function is 

provided by 

a 

pair of push-buttons on the panel at the lower 

left.  The off button lights when the High Voltage and the 

Emission are off. 

2 

HIGH VOLTAGE/EMISSION, ON- The on button lights when 

High Voltage and the Emission are on. 

The interlocks are sequential. That is, the first open interlock in the string is 

indicated and when it is closed, the next open interlock is indicated. When all 

interlocks are closed, all of the LEDs will be energized. If Zero Start is not 

engaged, no interlocks can light. 

� 

Note: There is a jumper on the motherboard for 

REMOTE- ON

� 

BYPASS

that also requires a jumper at J3 pins 5-6. 

This 2nd jumper may be applied at J103 on the back panel. 

3 

ZERO - This interlock insures that the emission control is at its 

minimum position before high voltage and filament voltage can 

be applied to the source.  The LED will light when the emission 

control knob is fully counterclockwise. For "AUTO" mode,  the 

input would need to be near 

o 

voe.

CONTROLS AND INDICATORS 

4-1 

Summary of Contents for TT-6


































Reviews:

No comments

Brands by name

Popular brands

Load more brands