Adjustment Procedure—2 213 Service
POWER SUPPLY AND CRT DISPLAY
Equipment Required (see Table 4-1)
Leveled Sine-Wave Generator (Item 2)
Digital Voltm eter (Item 11)
Time-Mark Generator (Item 3)
Test Oscilloscope and I X Probe (Item 12)
50+2 BNC Cable (Item 4)
DC Voltm eter (Item 13)
50+2 BNC Termination (Item 5)
Screwdriver (Item 14)
Variable Autotransformer (Item 10)
See
a t the back o f this manual fo r location o f test points and adjustments.
NOTE
Before applying pow er to the 2 2 1 3 , make the in itia l
control settings. Connect the 2 2 1 3 to an appropriate
pow er source through a variable autotransform er,
adjusted fo r an output o f 115 V. A pply pow er to
both the instrum ent and the test equipm ent and
allow a 20-m inute warm-up p erio d before com
mencing the adjustments and checks
INITIAL CONTROL SETTINGS
CRT
AUTO INTENSITY
As desired
AUTO FOCUS
Best focused display
Vertical (both)
POSITION
Midrange
VE R TIC A L MODE
CH 1
VO LTS/DIV
0.1 V
VO LTS/D IV Variable
CAL detent
AC-GND-DC
GND
Horizontal
POSITION
Midrange
HO RIZONTAL MODE
NO DLY
SEC/DIV
5 /is
SEC/DIV Variable
CAL detent
X10 Magnifier
O ff (knob in)
Trigger
VAR HOLDOFF
NORM
TRIGGER MODE
TV FIELD
TRIGGER SLOPE
J-
TRIGGER LEVEL
Midrange
INT
VERT MODE
SOURCE
INT
PROCEDURE STEPS
1.
C h e c k /A d ju s t P o w er Supply DC L ev els and
R ipple (R 946 and R 952)
NOTE
Review the information a t the beginning o f the Adjust
m ent Procedure before starting this step.
a.
Remove the High-Voltage shield (see the ‘ High-
Voltage Shield” removal procedure in Section 6) if the
instrument has the Current Limit board (A19). If the
instrument has the Preregulator board (A18), remove the
protective shield on the bottom of the Main board (A10) to
access the test point pads.
J V A R N I N t ^
To avoid electric shock and instrument dam age when
checking either the H ead Room Voltage o r the
Preregulator Output Voltage, use a digital voltmeter
that is isolated from ground, since the Inverter pow er-
supply circuitry common is a t line potential.
b.
Connect the digital voltmeter low lead to common
(TP934). If the instrument has the Current Limit board (A19),
connect the volts lead to TP952. If the instrument has the
Preregulator board (A18), connect the volts lead to TP940.
c.
CHECK— Reading is + 4.2 V to + 4 .4 V for instru
ments having the Current Limit board. Reading is 41 V to
44 V for instruments having the Preregulator board. If the
reading is within these limits, skip to part e.
5-4
REV NOV 1982
Summary of Contents for 2213
