P/N:0000000000
CCA
BCI
CA
MCA
JIS
DIN
IEC
EN
SAE
Ah
12V/60Ah/CCA 500A
300A EN
12V 250Ah 60Ah DIN
26A19R 12V 60Ah
26A19RMF 12V 60Ah
12V/60Ah
CCA
EN
DIN
JIS#
JIS#
AH
500
300
250A
200
220
60Ah
Overview
UT673A/UT675A battery tester, with its leading-edge conductivity test technology,
accurately and rapidly helps users to measure the cold cranking amps capability of the
vehicle starting battery, healthy state of the battery itself, detect the common fault of
vehicle starting and charging system, which helps repair vehicle quickly.
Safety information
Please carefully read this manual and follow the warning and safety information before
use.
To avoid fire and overcurrent, please read all rated values and symbol descriptions
before use.
Do not open the case cover. Do not turn on the tester if its cover or front panel is open.
Do not touch the connectors and components if the tester is powered on.
Please contact the authorized repair personnel to detect, repair, maintain the tester
if you find any fault on it.
Do not use in humid, explosive or inflammable environment.
Keep the tester surface clean and dry. Keep it well-ventilated.
Product introduction
Interface
UT673A
1) Battery: Battery test.
2) Crank: Vehicle Cranking system test.
3)
4) Data: The last test result can be viewed.
5) Setting: Language setting.
6) About: View the system information.
Charge: Vehicle Charging system test.
UT675A
2) Crank: Vehicle Cranking system test.
3)
4) Data: The last test result can be viewed or upload.
5) Print: Print test data.
6) Setting: Language and time setting, view the system information.
1) Battery: Battery test.
Charge: Vehicle Charging system test.
Feature
1) Applicable to 12V battery testing and 12V/24V vehicle cranking/charging system test.
2) Measurement standard and range:
100-2000
100-2000
100-2000
100-2000
26A17—245H52
100-1400
100-1400
100-2000
100-2000
30-200Ah
Measurement
range
Measurement
standard
Measurement
standard
Measurement
range
3) Working temperature: -20°C 50°C.
4) Special test clip: Double-conductor Kelvin clip.
5) Case material: Acid-resistant ABS plastic.
6) Measurement range of battery: 30Ah
—
200Ah.
7) Measurement range of voltage: 7V
—
16V.
8) Portable.
—
Example for selecting standard
Battery identification
Standard
Battery
parameter
Remark
12V battery, the capacity is 60Ah,
the cold-start current is 500A.
The standard value is 300A.
12V battery, the capacity is 60Ah,
the standard value is 250A.
12V battery, the capacity is 60Ah,
check JIS CODE conversion table
and find that 26A19R corresponds
to 220A for CCA.
12V battery, the capacity is 60Ah,
check JIS CODE conversion table
and find that 26A19R corresponds
to 220A for MF CCA.
If the standard is not found,
estimate CCA value according to
the battery capacity.
Operation instruction
1. Connect the red and black clips of tester to the measured battery, red is positive,
black is negative, the tester screen will display startup interface. If the battery voltage
is lower than 7.0V, the test will become abnormal.
2. According to the prompts, press up and down button to select:
UT673A:
①
Battery test,
②
③
Charging test,
④
View test results,
Cranking test,
⑤
System setting,
⑥
About.
UT675A:
①
Battery test,
②
③
Charging test,
④
View test results,
Cranking test,
⑤
Print test result,
⑥
Setting.
1. Make sure engine is off.
2. Connect to the correct polarity.
Battery
Crank
Charge
Data
Setting
About
Battery
Charge
Data
Setting
UT675A
UT673A
3. Select “Battery”
7. Press ENTER to start the test.
Description
The performance of storage battery is good,
please continue using the battery.
Because the voltage of storage battery is lower
than 12.3V, so the performance of storage
battery is good, please continue using the
storage battery after it is fully charged.
Because the battery voltage is lower than 12V, so please
retest after it is fully charged. Incorrect reading may occur
if the battery is not fully charged. Please replace the battery
if “Retest after charging” displays again after charging.
The battery is in
good condition.
The battery is in
good condition,
please charge
the battery.
Retest after charging
Replace the battery
The battery is in bad
condition, replace
the battery.
Replace the storage battery.
Battery inside is damaged, replace the storage battery.
Battery capacity (SOC): The percentage of remaining battery capacity,
1)
2) Battery voltage (VOLTAGE): The voltage value of storage battery (Unit: V).
Battery life (SOH): State of health of battery storage,
3)
The measured cold-start current: The measured cold-start current of tester.
4)
Nominal cold-start current: Nominal cold-start current of storage battery
5)
Internal resistance of battery (R): The measured internal resistance of storage battery.
6)
NOTE: For low-capacity battery (For example, the vehicle is shut down for a long
time, the battery is not charged in time, the battery power is significantly lost
because the vehicle door is not closed.), the tester may prompt you to “Replace
battery” during actual measurement, please consult the storage battery factory
and charge the battery according to the designated method, and then retest.
SOC= ×100%.
Remaining capacity
Actual capacity
SOH= ×100%.
Actual capacity
Nominal capacity
UT673A/UT675A Battery Tester
Battery
Crank
Charge
Data
Setting
About
Battery
Crank
Charge
Data
Setting
UT675A
UT673A
Tests below are based on 12V, 60Ah, CCA580A:
1. Battery test
Crank
Battery Test results
Interpretation
2. Cranking test
1. Make sure engine is off.
2. Connect to the correct polarity.
Battery
Crank
Charge
Data
Setting
About
Battery
Charge
Data
Setting
UT675A
UT673A
3. Select “Crank”
4. Enter the interfaceof
starting engine.
Crank
NORMAL BAT.
AGM ATTERY
B
EFB ATTERY
B
GEL ATTERY
B
TYPE
4. Select “NORMAL BAT”
CCA
DIN
JIS
EN
ST
ANDARD
5. Select standard,CCA for example.
580 A
CCA
SET RATING
6. Set rated capacity of battery.
TESTING
SOH 75
%
495A
SOC 100
%
12.8V
R= 3.35m
Ω
GOOD BATTERY
8. Display test result.
CRANKING TEST
START ENGINE
5. Start engine.
RPM DETECTED
CRANKING TEST
6. Engine RPM is detected.
TESTING
CRANKING NORMAL
CRANKING 11.34V
TIME 243ms
7. Automatically enter the test.
8. Display test result.
