Team Blacksheep CAIPIRINHA II Manual Download

Page: 19 / 30

Electronics installation

The TBS CAIPIRINHA II is designed to be flown light and with any FPV equipment, powertrain and battery

system, while reducing the build time to a minimum when building it with TBS-designed. Several central

cable channels keeps the wires neatly tucked away.

Central to the power powertrain is the power distribution board (PDB). It provides a quick way to connect

and replace the battery, no more loose power wires. Additional batteries can be connected to the free

XT60 footprints.

When picking out suitable equipment, keep lightweight and small size as key factors for a successful build.
The compartment layout is layed out to provide optimal separation between the R/C control link and VTX

video link. This extends range and minimized induced noise between the systems.

A detailed electronics installation diagram is available as an appendix to this manual.

Summary of Contents for CAIPIRINHA II































Search results

Summary of Contents for CAIPIRINHA II

Reviews:

Related manuals for CAIPIRINHA II

Brands by name

Popular brands

Team Blacksheep CAIPIRINHA II, Manual

Search results

Summary of Contents for CAIPIRINHA II

Reviews:

Related manuals for CAIPIRINHA II

Brands by name

Popular brands