TCS AMI11603 Product Information Download Page 4

 

Safety instructions 

General safety regulations 

 

Assembly, installation, commissioning and repair of electronic devices must be carried out by qualified 
electricians.  
Observe the latest regulations and standards for system installations. 

 

 

WARNING!  Danger to life due to electric shock 

Observe the safety regulations according to DIN VDE 0100, when working on main power connections of 
230 V. 

 

 

When installing TCS:BUS systems the general safety regulations for telecommunication systems ac-
cording to VDE 0800 must be observed. Inter alia: 

  separated cable routing of high and low voltage lines, 

  minimum distance of 10 cm in case of a common cable routing, 

  use of separators between high and low voltage lines within shared cable ducts, 

  use of standard telecommunication lines, e.g. J-Y (St) Y with 0.8 mm diameter, 

  already existing lines (modernisation) with deviating cross-sections can be used in compliance with 

the loop resistance. 

 
 

Requirements to protect against lightning  

 

ATTENTION!  Device damage due to over-voltage 

By suitable lightning protection measures it has to be ensured that the electric voltage of 32 V DC at each 
connection is not to be exceeded. 

 
 

Product description 

Intended use 

The display module LCD graphic AMI11603is a module of the front-door station series AMI. The display module 
LCD graphic AMI11603 is suitable for the operation in TCS video systems and combined audio / video systems. 
The display module can be used only in combination with a built-in door loudspeaker module AMI11x0, a codelock 
module AMI11200 or another module with a 4-pin connection cable. The display module cannot be combined with 
the jogwheel module AMI10400 and the keypad module AMI10300. In combination with the jogwheel module 
AMI10410 (with reduced speed) a quick and easy selection within in the list is feasible. In combination with the 
codelock module AMI11200 (operating mode: keyboard) a direct input of flat numbers at the codelock module is 
possible. 
 

 

For applications, which differ from the intended use or goes beyond it, the manufacturer accepts no lia-
bility. 

Short description 

  for up to 256 flats  

  fully graphical, monochrome display with 160 x 104 pixel, white backlight 

  residents can be called via an alphabetical sorted name list (optionally via input of the flat number or access code 

via codelock module) 

  language can be changed, also non-Latin characters can be displayed 

Summary of Contents for AMI11603





















Reviews: