TCS AMI11603 Product Information Download Page 19 | Manualshive

Page: 19 / 20

TCS AMI11603 Product Information Download Page 19

19

Cleaning

ATTENTION Loss of function due to short-circuit and corrosion.

Water and cleaning agents can enter the device. Electronic components can get damaged due to short-
circuit and corrosion.
Avoid water and detergents from entering the device. Clean the device with a dry or slightly wet cloth.

ATTENTION! Damages on the surface of the device.

Abrasive and scratching detergents damage the surface of the device.
Do not use any abrasive detergents!
Remove stronger stains with a pH neutral household cleaner.

Conformity

Declarations of conformity are available for download under www.tcsag.de.

Information on disposal

Dispose the device separately from domestic waste via a collection point for electronic scrap. Ask your
county administration for the responsible collection point.

Dispose the parts of the packaging in collecting tanks for cardboard and paper resp. plastics.

Warranty

We offer

a simplified processing

in case of warranty for qualified electricians.



Please contact the

TCS HOTLINE

under

[email protected]

.



Our

standard terms and conditions of sale

you'll find under www.tcsag.de.

«
...
17
18
19
20
»

Summary of Contents for AMI11603





















Reviews:

No comments