background image

3/ 42 

User Notice   

This manual is compiled by Guangdong TAYO  Motorcycle Technology Co., Ltd. And is used to guide dealers or service 

personnel. This manual cannot provide more detailed knowledge about motorcycles, and is only for reference for maintenance. 
If you do not have the corresponding knowledge such as electrician, machine repair, etc., improper assembly or maintenance 
failure may occur during repair. 

If you need to clean or wash the body parts of this motorcycle, you should use neutral car wash liquid or tap water or diesel 

oil, kerosene, etc. Acidic or alkaline car wash liquid will cause irreversible corrosion to the surface paint, electroplated surface, 
anodized surface, etc. Of parts; gasoline will cause premature aging or hardening of sealants, gaskets, rubber parts, etc., reducing 
the service life. It should be wiped with a non-woven cloth that will not leave residues. Ordinary rags may leave rags or wool that 
will affect assembly or cause other adverse effects. 

Our company tries to update this manual in a timely manner after product changes. 
 

The following are the meanings of the icons marked in this manual: 

 

Failure to comply will result in personal injury or death of the driver or maintenance 
personnel ; or serious damage to spare parts , shortened service life, etc. 

 

Failure to comply may result in personal injury or death of the driver or maintenance 
personnel ; or damage to spare parts , abnormality, etc. 

 

Failure to follow the warnings will result in personal injury to the driver or 
maintenance personnel ; or matters requiring special attention during disassembly 

 

Indicates that there is a requirement for torque 

 

Indicates that the part needs to be replaced after disassembly 

 

Indicates that the location needs to be measured 

 

 

Summary of Contents for ZT1P52MI











































Reviews: