background image

3

CCD-0004215 

   

Rev: 02.18.21

Safety

Read and fully understand all instructions before installing or operating 

this product. Adhere to all safety labels. This manual provides general 

instructions. Many variables can change the circumstances of the 

instructions, i.e., the degree of difficulty, operation and ability of the 

individual performing the instructions.
This manual cannot begin to plot out instructions for every possibility but 

provides the general instructions, as necessary, for effectively interfacing 

with the device, product or system.
Failure to correctly follow the provided instructions may result in death, 

serious personal injury, severe product and/or property damage, 

including voiding of the LCI limited warranty.

DO NOT SIT OR STAND ON THE FLAGPOLE MOUNT.

DO NOT USE THE FLAGPOLE MOUNT TO TOW ANOTHER BOAT 

OR ANY OTHER APPARATUS.

DO NOT USE THE FLAGPOLE MOUNT AS A HAND GRAB BAR TO 

PULL A SWIMMER ONTO THE BOAT.

WHEN PULLING A SKIER OR A TUBE, MAKE SURE THE FLAG 

INSERTED INTO THE FLAGPOLE MOUNT IS NOT TOO LARGE. 

IF THE FLAG IS TOUCHING THE SKI ROPE, THE FLAG MUST BE 

REMOVED.

Summary of Contents for KW Series









Reviews: