Cantilever Flat Panel Bracket
Installation instruction for 803B
TV Size:36 -65"
"
Tilt :-5
/
15
Max
Load
capacity
:
132lbs/60kgs
Wall
Distance
:
5.8 -22.8"/
147
-
580mm
"
Bubble
level
system
Included
Universal
Mounting
Pattern
Hardware kit:
Tools Required:
PLASMA MOUNT INSTALLATION AND OPERATION INSTRUCTION
√
√
√
√
Phillips Head Screw driver
Stud finder for drywall installation
Socket and Wrench
Electric drill masonry bit for concrete/brick installation
A
B
C
D
E
F
(×4) M6×16 screw
(×4) M8×16 screw
(×4) M5×35 screw
G
H
I
J
K
L
M
(×4) M6×35 screw
(×4)
M8×35 screw
(×4) M8/M6/M5 Washer
(×4) M8 Bolt
(×4) M8 concrete anchor
(×4) M8 Washer
(×4) M8 Spacer
N
(×4) M5×16 screw
(×2) M6 concrete anchor
(×4) M6 Bolt
(×4) M6 Washer
Note:
1
You need rivet the bubble level system onto the wall plate before installing
2
Please check the two rails before installing,if without the knob as showed, please
first detach the screw and install the knob.
Step1: Wall plate installation
Wood Stud Installation
NOTE:For secure wood stud mounting,the wall plate must be mounted to two studs at least 16"apart.
Concrete/Brick Installation
The concrete anchors must be used for concrete installation.
NOTE:
1
Begin by placing the wall plate into position against the wall,
using the bubble level to keep it level.
2
Mark off 6 holes to be used for securing the mount and
place the wall plate aside
3
Next , drill holes four 8mm holes 40mm deep(M6 bolt J) and
four 12mm holes 60mm deep (M8 bolt I)
4
Insert a concrete anchor(K)into to reach hole.
5
If necessary, a hammer can be used to lightly tap each anchor
into place so that they are flush with the wall.
7
Attch the bolt(I/J) into the anchor(H) that is placed in the wall.
8
Do not tighten until all screws are in plate .
1
Use a high-quality electrnic stud finder (commercially available) to locate two adjacent studs and
mark their locations with a pencil.
2
With the help of an assistant, and using the bubble level to ensure the wall plate is level, position
the wall plate against the wall in the desired mounting location.
3
Mark the right, upper and lower and the left (upper and lower) positions of the small horizontal slots
that are in alignment with the studs.
4
You should mark eight positions total as the picture showed.
5
Next, Pre-drill four 3mm hole 30mm deep on the up wall plate for M6 bolt (J) and four 5mm holes
50mm deep for M8 bolt(I) as showed following.
6
please position the wall plate against the wall and line up the mounting slots with drilled holes
7
For each location, insert a lag bolt
(
I
/
J
)
and
washer
(
L/M
)
into
the
wall
.
8
Tighten bolt with an open ended socket wrench by turning clockwise until tight.
IMPORTANT:If you don't understand how to install the product,
please consult a specialist
6
Once all of the anchors are in place ,move the wall plate back into position.
Please add the back cover
firstly as the picture
BALANCE-ADJUSTING
J
I
M
L
I
L
(J)M6X80
3mm
5mm
30mm
60mm
(I)M8X80
H
G
M
L
I
J
(J)M6X80
8mm
12mm
40mm
60mm
(I)M8X80
BALANCE-ADJUSTING
