TAJIMA TFHX Series, User Manual

Page: 27 / 140

CHAPTER 3 OPERATION BASICS
20
7. PANEL SOFTWARE INSTALLATION
This operation is necessary when setting up
machine and/or upgrading the software.
Start the operation from a state of turning
“ON” the power.
1. Insert the PANEL software to the FDD
2. Switch to the screen 3000
3. Display switching of the screen 3000
Press each of P3, P5, and ADJ two times,
and then press INF.
4. Take note of setting value
Take note of the contents of the following
parameter setting.
61. Max. Revolution [rpm]
64. Number of Needles
65. Number of Heads
66. Model (TEHX-C is invalid)
It will become necessary to set parameters as
described above when confirming them after
installation of the software.
CAUTION
Before installing the PANEL software, save the design data currently reg-
istered in the memory to a floppy disk. Design data may be damaged by
unexpected causes during installation.
!
(GC07)
PA
N
E
L
Screen 1000
1
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
22. Return Stitches (ATH)
23. Tie Stitches
24. Tie stitching/return stitching amount [mm]
25. Preset Halt (Stitch)
26. Preset Halt (Data)
27. Preset Halt (Design)
28. Preset Halt (Lubrication)
29. Preset Halt (Just before End Code)
30. Language
( -, 1, 2, )
( No, Yes, )
( 0.6, 0.8, )
( 0 ~ 999999 st., )
( 0 ~ 99999 cm, )
( 0 ~ 999 Designs, )
( 0 ~ 99 * 10000 st., )
( No, Yes, )
( English, Japanese, Other, )
-
Yes
0.8
0
0
0
0
No
English
----
22. Return Stitches (ATH)
23. Tie Stitches
24. Tie stitching/return stitching amount [mm]
25. Preset Halt (Stitch)
26. Preset Halt (Data)
27. Preset Halt (Design)
28. Preset Halt (Lubrication)
29. Preset Halt (Just before End Code)
30. Language
( -, 1, 2, )
( No, Yes, )
( 0.6, 0.8, )
( 0 ~ 9999 * 100 st., )
( 0 ~ 9999 * 10 cm, )
( 0 ~ 999 Designs, )
( 0 ~ 99 * 10000 st., )
( No, Yes, )
( English, Japanese, Other, ) 2
No
38400
No
0.0
0.0
41. Boring Step
42. Cording
-----
-----
45. Network
46. Serial speed [bps]
-----
48. Table Up/Down
49. Backlash (X Axis) [mm]
50. Backlash (Y Axis) [mm]
( No, Yes, )
( 9600, 19200, 38400, )
( No, Yes, )
( -0.5 ~ 0.5, )
( -0.5 ~ 0.5, )
----
----
No
No
51. Total Stitch Counter
52. Display of M.Shaft Stop Position
53. Display of Needle Position
54. PANEL software Install
-----
56. Stop at Lower D.Point
( , )
( , )
( No, Yes, )
( No, Yes, )
12
4d
2C
----
61. Max. Revolution [rpm]
----
----
64. Number of Needles
65. Number of Heads
66. Model
67Frame Drive Mode
----
69. CPU Software Version
----
( 3, 6, 9, 12, 15, 18, )
( 2, 3, 4r, 4d, 5, 6, 7, 8, )
( 2, 2C, L, LC, N, NC, )
( 500 ~ 1100, )
( , )
3
4
5
Step1
( Step1, Step3, )
( ---, 0, )
----
1000
1000
( No, Yes, )
No
57. Frame Travel Key
( 4, 8, )
4
( Auto, 210, )
Auto
Screen 3000
12
4d
2C
----
61. Max. Revolution [rpm]
----
----
64. Number of Needles
65. Number of Heads
66. Model
67. Frame Drive Mode
----
69. CPU Software Version
----
( 3, 6, 9, 12, 15, 18, )
( 2, 3, 4r, 4d, 5, 6, 7, 8, )
( 2, 2C, L, LC, N, NC, )
( 500 ~ 1100, )
( , )
1000
1000
( Auto, 210, )
Auto